Motor Driver 2a Dual L298 H Bridge Results at Top10Bot.com

  • PChero 2Packs L298N Motor Drive Controller Board Module, Dual H Bridge DC Stepper For Arduino Smart Car Robot

    Why CHOOSE PChero Motor Drive Controller Board Moduld? Reason 1: Use L298N for Main Chip L298N is a kind of high voltage, high current motor driver chip. Having 15 pins as package, this chip has such features as high working voltage(maximum voltage up to 46V),large output current(instantaneous peak current up to 3A, continuous working current 2A) and 25W of rated power. Two built-in H birdge high voltage and large current full bridge drivers can be used to drive the DC motor and stepper motor, relay coil and so on.Using standard logic level signal control, it has two enable control ends. It permits or prohibites device having a logic power su...
    Motor Driver 2a Dual L298 H Bridge

    • ASIN: B07C4B3DL4
    • Brand: PChero
    • UPC: 712809501328

  • DC Motor Driver, DROK L298 Dual H Bridge Motor Speed Controller DC 6.5V-27V 7A PWM Motor Regulator Board 12V 24V Electric Motor Control Module Industrial 160W with Optocoupler Isolation

    Parameters: 1. Power supply voltage 6.5V-27V, the power cannot be reversed or over 27V, or may burn the module, it is recommended connecting in series 15A fuse in the power input. 2. Dual motor interface, each rated output current 7A, peak current 50A, the motor interface cannot short-circuit, it is recommended connecting in series 15A fuse. 3. The enable signal and forward and reverse control signal control voltage 3-6.5V. 4. Enable signal terminal (ENA) input PWM can regulate speed, PWM frequency range 0-10KHZ, PWM minimum pulse width 10us. 5. Product dimension: 55x55x16mm  6. Installation hole diameter: 3mm, noted to prevent short circuit...
    Motor Driver 2a Dual L298 H Bridge

    • ASIN: B06XGD5SCB
    • Brand: DROK
    • UPC: 701822755689

  • Qunqi 2Packs L298N Motor Drive Controller Board Module Dual H Bridge DC Stepper For Arduino

    Specification: Chip: L298N Logic voltage: 5V Logic current 0mA-36mA Storage Temperature: -20 ℃ to ℃ to +135 Operating mode: H-bridge driver (dual) Drive voltage: 5V-35V Drive current: 2A (MAX single bridge) Maximum power: 25W Dimensions: 43x43x27mm Package include: 2x L298N Module Note: This module has a built-in 5v power supply, when the driving voltage is 7v-35v, this supply is suitable for power supply DO NOT input voltage to +5v supply interface, however ledding out 5v for external use is available. When ENA enable IN1 IN2 control OUT1 OUT2 When ENB enable IN3 IN4 control OUT3 OUT4...
    Motor Driver 2a Dual L298 H Bridge

    • ASIN: B01M29YK5U
    • Brand: Qunqi

  • Qunqi L298N Motor Drive Controller Board Module Dual H Bridge DC Stepper For Arduino

    Specification: Chip: L298N Logic voltage: 5V Logic current 0mA-36mA Storage Temperature: -20 ℃ to ℃ to +135 Operating mode: H-bridge driver (dual) Drive voltage: 5V-35V Drive current: 2A (MAX single bridge) Maximum power: 25W Dimensions: 43x43x27mm Package include: 1x L298N Module Note: This module has a built-in 5v power supply, when the driving voltage is 7v-35v, this supply is suitable for power supply DO NOT input voltage to +5v supply interface, however ledding out 5v for external use is available. When ENA enable IN1 IN2 control OUT1 OUT2 When ENB enable IN3 IN4 control OUT3 OUT4...
    Motor Driver 2a Dual L298 H Bridge

    • ASIN: B014KMHSW6
    • Brand: Qunqi
    • UPC: 783325944715

  • TIMESETL 5Pack L298N Stepper Motor Driver Controller Board Dual H Bridge Module for Arduino Electric Projects

    L298N of TIMESETL TIMESETL Motor Drive Controller - High Quality Specification: Size: 43*43*27mm/ 1.69*1.69*1.06 inch Dual H bridge drive (can drive 2 DC motors) Chip: L298N Logical voltage: 5V Drive voltage: 5V-35V Logic current: 0mA-36mA Drive current: 2A(For each DC motor) Weight: 30g TIMESETL L298N DC Stepper Motor Drive - Usage Great for Arduino, Smart Car, Power UNO, MEGA R3, Mega 2560, etc If driving voltage is more than 12V, please use external 5volt logic outputs to switch the H-bridge circuits. Delivery 5 x L298N Stepper Motor Controller...
    Motor Driver 2a Dual L298 H Bridge

    • ASIN: B078D7DR9V
    • Color: L298N Driver
    • Brand: TIMESETL
    • UPC: 611702529715

  • DAOKI 5 PCS L298N Motor Drive Controller Board DC Dual H-Bridge Robot Stepper Motor Control and Drives Module for Arduino Smart Car Power UNO MEGA R3 Mega2560

    L298N is a kind of high voltage,high current motor driver chip produced by ST company.Having 15 pins as package, this chip has such features as high working voltage(maximum voltage up to 46V),large output current(instantaneous peak current up to 3A,continuous working current 2A) and 25W of rated power.Two built-in H birdge high voltage and large current full bridge drivers can be used to drive the DC motor and stepper motor,relay coil and so on.Using standard logic level signal control,it has two enable control ends.It permits or prohibites device having a logic power supply input without the impact of input signal,which enables the internal ...
    Motor Driver 2a Dual L298 H Bridge

    • ASIN: B00XAGRQTO
    • Color: L298N
    • Brand: DAOKI
    • UPC: 695259095961

  • Anmbest 5PCS L298N Dual H Bridge DC Stepper Motor Driver Controller Board Module for Arduino Smart Car UNO R3 Raspberry Pi Mega2560

    Double H driver module uses ST L298N dual full-bridge driver, an integrated monolithic circuit in a 15- lead Multiwatt and PowerSO20 packages. It is a high voltage,high current dual full-bridge driver designed to accept standard TTL logic levels and drive inductive loads such as relays, solenoids, DC and stepping motors. Two enable inputs are provided to enable or disable the device independently of the input signals.The emitters of the lower transistors of each bridge are connected together and the corresponding external terminal can be used for the con-nection of an external sensing resistor. An additional supply input is provided so that t...
    Motor Driver 2a Dual L298 H Bridge

    • ASIN: B07CQZ655K
    • Brand: Anmbest

  • Aideepen 5pcs 1.5A 2 Way DC Motor Driver Module Speed Dual H-Bridge Replace Stepper L298N

    Description: Motor drive module is ideal for use in battery-powered smart car, toy cars, robots. Supply voltage 2V ~ 10V, can drive two DC motors or a 4-wire 2-phase stepper motors ,can achieve forward rotation or reverse rotation, it is possible to adjust the rotation speed. Each can provide continuous current of 1.5A, peak current up to 2.5A, thermal protection and can be automatically restored. Product parameters: The module supply voltage 2V-10V. Signal input voltage 1.8-7V. Single Operating current 1.5A, peak current up to 2.5A, low standby current (less than 0.1uA). Built-in common conduction circuit, when the input pin is left floati...
    Motor Driver 2a Dual L298 H Bridge

    • ASIN: B075S368Y2
    • Brand: Aideepen
    • UPC: 783057981521

  • L298N Motor Driver Controller Board Module Stepper Motor DC Dual H-Bridge for Arduino Smart Car Power UNO MEGA R3 Mega2560

    Features: ✈This module uses the genuine L298 double H-bridge motor driver chip. The stable and strong driving force. ✈The operating voltage is high, up to 46V; the steady current is 2A, and the instantaneous peak current can reach 3A. ✈The dual H-bridge design can drive two DC motors or one DC motor and one stepper motor simultaneously. ✈The design is small, small and practical. Can be used for a long time and repeated. ✈Built-in overheat protection circuit will automatically resume working after the temperature drops. ✈Carry two DuPont cables to connect the module to other devices. Parameter: Size: 43*43*27mm/ 1.69*1.69*1.06 inch...
    Motor Driver 2a Dual L298 H Bridge

    • ASIN: B07T537ZXY
    • Color: 5 Pack
    • Brand: HUKER
    • UPC: 793707166314

  • L298N Motor Drive Controller Board Module Dual H Bridge DC Stepper Module for Arduino & Male to Male/Male to Female/Female to Female Breadboard Jumper Wires Ribbon Cables Kit, Ltvystore

    Ltvystore 5Pack L298N Motor Drive Controller Board Chip: L298N Logic voltage: 5V Logic current 0mA-36mA Storage Temperature: -20 ℃ to ℃ to +135 Operating mode: H-bridge driver (dual) Drive voltage: 5V-35V Drive current: 2A (MAX single bridge) Maximum power: 25W Dimensions: 43x43x27mm/1.69"x1.69"x1.1"(L*W*H) Note: This module has a built-in 5v power supply, when the driving voltage is 7v-35v, this supply is suitable for power supply. DO NOT input voltage to +5v supply interface, however ledding out 5v for external use is available. When ENA enable IN1 IN2 control OUT1 OUT2 When ENB enable IN3 IN4 control OUT3 OUT4 L298N motor con...
    Motor Driver 2a Dual L298 H Bridge

    • ASIN: B07W8TS27G
    • Brand: Ltvystore
    • UPC: 823717594644

  • Dayton Round Motor Dual Run Capacitor, 45/5 Microfarad Rating, 370VAC Voltage - 2MEF4

    Dayton Round Motor Dual Run Capacitor, 45/5 Microfarad Rating, 370VAC Voltage - 2MEF4
    Motor Driver 2a Dual L298 H Bridge
    The Dayton 2MEF4 is a hermetically sealed capacitor designed to improve the electrical performance of motors, air conditioners, and refrigeration equipment. The unit is PCB-free and features an aluminum case with a steel cover. The unit also offers protection to 10,000 AFC.About this capacitor:Microfarad Rating: 45/5, Voltage: 370V, Hz: 60/50, Shape: Round, Diameter: 2-3/8", Case Height: 4-3/4", Overall Height: 5-1/4", Overall Width: 2-3/8", Terminal Type: 1/4" Male Quick-Connect, Temp. Range: -40 Degrees to 70 Degrees C, Case Material: Aluminum, Cover Material: SteelStandards: cULs Recognized

    • UPC: 991168027
    • Color: Multicolor
    • Rating: 5.0

  • Dual Channel L298N DC Motor Driver Board PWM Speed Dual H Bridge Stepper Module Red

    Please note, this item ships from an international seller. Expected delivery is 10-15 days.Dual Channel L298N DC Motor Driver Board PWM Speed Dual H Bridge Stepper ModuleFeatures:1.Dual H-bridge motor driver, can drive two DC motors or a 4-wire two-phase stepper motors2.Built-in TSD, without worrying about motor stall3.Ultra-small size, suitable for assembly and carSpecification:1.Module supply voltage: DC 2V-10V2.Signal input voltage: DC 1.8-7V3.Single working current: 1.5A4.Peak current up to 2.5A5.Low standby current (less than 0.1uA)6.Built-in common conduction circuit, the input terminal vacant, the motor does not malfunction7.Size: 24.7 x 21 x 7mm8.Mounting hole diameter: 2 mmGeneralConnectivity Electronic ComponentsMicroprocessorsPower BatteriesCertificationDimensions and WeightProduct weight0.0100
    Motor Driver 2a Dual L298 H Bridge
    Dual Channel L298N DC Motor Driver Board PWM Speed Dual H Bridge Stepper Module Red

    • UPC: 896958731

  • L298 Dual H-Bridge Motor Driver

    L298 Dual H-Bridge Motor Driver
    Motor Driver 2a Dual L298 H Bridge
    L298 Dual H-Bridge Motor Driver

    • UPC: 274301583

  • L298N DC Stepper Motor Driver Module Dual H Bridge Control Board for Arduino

    SpecificationsDouble H bridge driveChip L298N (ST NEW)Logical Voltage: 5VDriving Voltage: 5V-35VLogic current: 0mA-36mADrive Current: 2A (MAX Single Bridge)Storage temperature: - 20 to ± 135℃Max power: 25WWeight: 30gSize: 43 * 43 * 27mmPackage includes1 * L298N DC stepper motor module (excluding
    Motor Driver 2a Dual L298 H Bridge
    Using L298N made by ST company as the control chip, strong driving ability, low heat value and strong anti-interference ability.This module can use built-in 78M05 for electric work via a driving power supply part.But please avoid the damage of the voltage stabilizing chip, use an external 5V logic power supply when using more than 12V driving voltage.Using large capacity filter capacitor, this module can follow current to protect diodes, and improve the

    • UPC: 641187840

  • L298N Stepper Motor Driver Controller Board Dual H Bridge Module for Arduino Electric Project

    Great Sensors for Arduino Project. Having Fun With Electronics and Programming! Description:Widely use in computers, printers, copiers, alarms, electronic toys, automotive electronic equipment, telephones, timers and other electronic products for sound devices.If driving voltage is more than 12V, please use external 5volt logic outputs to switch the H-bridge circuits. Specification:Chip Model: L298NOperating Model: H-bridge driver (Dual)Logical Voltage: 5VDrive Voltage: 5V-35VWorking Voltage: DC 5V-35VLogic Current: 0mA-36mADrive Current: 2A (MAX single bridge)Maximum Power: 25WPCB Size: 43mm x 43mm (L*W)Fixed Hole Dia.: 3mmFixed Hole Distance: 37mm x 37mm Package Includes:1 x L298N Stepper Motor
    Motor Driver 2a Dual L298 H Bridge
    L298N driver chip makes strong driving ability, small heating, strong anti-interference and low calorific valueUse large-capacity filter capacitors and diode with freewheeling protection function to increasing reliabilityDual-channel H-bridge driver working mode creates higher working efficiencyTo avoid harm the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving

    • UPC: 883249546

  • Controlling DC Motors with the L298N H Bridge and Arduino

    Motor Driver 2a Dual L298 H Bridge
    Get more info about using the L298N at https://dbot.ws/l298nhbr More projects and tutorials at https://dronebotworkshop.com Pick the topic for my future videos - https://dbot.ws/dbnews The L298N D...
    L298,L298N,Motor Controller,H-Bridge,Arduino (Computing Platform),DC motor,L298N Dual H Bridge,Ro...

    L298N H-bridge DC MOTOR DRIVER

    Motor Driver 2a Dual L298 H Bridge
    L298N H-bridge DC MOTOR DRIVER ( MakeloGy ) - Dual Motor Controller Module 2A with Arduino. This allows you to control the speed and direction of two DC motors, or control one bipolar stepper m...
    MakeloGy,arduino,dc motor,l298n,howto,electric motor control,robot,electronics,technology,gadget,...

    How to connect your “L298N Dual H-Bridge Motor Controller” to “Arduino Uno”

    Motor Driver 2a Dual L298 H Bridge
    In this video, you will learn how to control a dc motor with the help of Arduino Uno using an L298N dual H-bridge motor controller. ►Arduino Uno: Arduino Uno is a microcontroller board based on th...
    L298N Dual H-Bridge Motor Controller,Arduino Uno,Motor Controller,How to connect your “L298N Dual...